Thermoplastic Polyurethane

TPU

ESSENTIAL The only flexible filament that matters

TPU is the flexible material category. If you need something that bends, compresses, or absorbs impact, TPU is what you're printing. Comes in hardnesses from 85A (very flexible) to 98A (semi-rigid). Processing depends entirely on your machine — bowden setups range from difficult to impossible at soft TPU grades, while direct drive runs it reliably.

Print Settings
Nozzle Temp 220–240°C
Bed Temp 30–60°C
Chamber None required
Cooling Fan 30–50%
Max Speed 30–50 mm/s
Heat Deflection N/A (flexible)
Difficulty Intermediate
Updated 2026-06-01
At a glance
Pros
  • The only common flexible filament — nothing else provides rubber-like behavior
  • Excellent impact absorption — best material for bumpers, grips, pads
  • Chemical resistance — handles oils, mild solvents, abrasion
  • UV resistant compared to PLA
  • Variable hardness options — 85A to 98A covers most use cases
Cons
  • Slow — 30–50mm/s is the ceiling for most setups
  • Not bowden-compatible at soft grades
  • Strings aggressively — requires active management
  • Not stiff — cannot be used for structural parts under load
  • Poor bridging — flexible material sags more than rigid alternatives
Overview

TPU is irreplaceable. If a part needs to flex, grip, absorb impact, or seal against something, TPU is the answer; there’s no rigid-filament substitute. Phone cases, cable boots, gaskets, vibration dampeners, TPU flex couplings, gripper pads, protective bumpers: the use cases are everywhere.

The hardness number matters. 95A is the default: flexible enough for most uses, stiff enough to print without constant trouble. 85A prints like soft rubber and requires a very dialed direct-drive setup. 98A is almost rigid and processes more like PETG than rubber.

Disable pressure advance in Klipper when running TPU. The algorithm fights the material’s natural compliance and causes under-extrusion artifacts. Same for input shaping; don’t run it at TPU speeds.

Use it for: phone cases and grips, cable management and organizers, vibration dampening mounts, flexible hinges, gaskets, protective bumpers, conveyor belt parts, shoe insoles, prosthetic sockets.

Don’t use it for: structural parts under tensile or compressive load, anything that needs to be rigid, bowden-drive printers with soft grades.

Brand Recommendations
Bambu Lab TPU 95A TOP
$29.99/kg

AMS compatible — the only TPU to credibly claim this. Requires careful humidity management in AMS. Excellent for Bambu users who want flexible parts without a separate workflow.

Polymaker PolyFlex TPU95 TOP
$27.99/kg

Community favorite. 95A hardness is the best all-around. Prints reliably on direct drive without special tricks. Excellent diameter consistency.

Ninjatek Armadillo (75D / ~95A) TOP
$49.99/kg

Semi-rigid with excellent abrasion resistance. Industrial-tier consistency. Best for mechanical parts that need some flex but not full rubber behavior. Expensive but worth it for critical parts.

Ninjatek Cheetah 95A TOP
$39.99/kg

High-speed TPU from Ninjatek. Prints faster than standard TPU. Justified for production volume.

SUNLU TPU MID
$16.99/kg

Works on direct drive at slow speeds. More variable diameter than premium options. Good for non-critical flexible parts.

Hatchbox TPU MID
$21.99/kg

Reliable, widely available. Runs at 230°C without issue on direct drive. Acceptable quality for most applications.

Troubleshooting
Coiling inside extruder / jams
Cause Too fast, too much retraction, or printing bowden
Fix Max 30mm/s for 95A. Zero or 0.5mm retraction only. Bowden setups: not recommended for 95A, essentially impossible for 85A. Direct drive strongly preferred.
Stringing
Cause TPU strings easily — high temp + long travel
Fix Lower temp to 220°C. Enable Wipe on retract. Minimize travel moves in slicer. Coasting helps on some setups.
Under-extrusion at perimeters
Cause Extruder gears chewing through soft material
Fix Reduce extruder tension slightly. Print slow. Dual-drive extruders (Orbiter, BMG) handle TPU better than single-drive.
Poor bed adhesion
Cause TPU on smooth PEI can be tricky
Fix Textured PEI is better. Clean with IPA. 50°C bed. Glue stick not required but helps on first print with a new surface.
Elephant's foot / spread
Cause TPU flows at lower pressure — first layer squish is hard to control
Fix Back off live Z offset compared to PLA. TPU compresses more. First layer should look slightly underfed compared to PLA targets.
Printer Compatibility
Printer Rating Notes
Bambu X1C / P1S EXCELLENT AMS compatible with Bambu TPU specifically. Third-party TPU works in single-spool mode. Textured PEI plate. Use TPU profile.
Bambu A1 / A1 Mini GOOD AMS Lite compatible with 95A+ TPU. Softer grades (85A) will jam. Direct spool feed more reliable.
Voron 2.4 EXCELLENT Direct drive extruder makes TPU easy. Clockwork or Orbiter recommended. Disable pressure advance for TPU.
Voron Trident EXCELLENT Same as 2.4.
RatRig V-Core 3 EXCELLENT Direct drive. Disable pressure advance. Open enclosure door to prevent heat creep on long prints.
Prusa MK4 GOOD Direct drive. Run at 25–30mm/s for 95A. 85A grades require extra care — reduce speed further and watch for coiling in extruder.