Home / Voron / Electronics

Electronics for Voron 2.4 & Trident

The electronics stack — mainboard, host computer, toolboard, and PSU — determines your wiring complexity, feature set, and upgrade path. Klipper runs on all of these. The main decision is how much you want to simplify your wiring loom with CAN bus.

Showing parts for: Voron 2.4 Switch model →
CAN bus vs traditional wiring The EBB36 toolboard cuts your toolhead wiring from ~12 conductors to 2 (CAN + 24V). It requires a CAN-capable mainboard (Octopus Pro or Manta M8P) and a USB-to-CAN bridge or onboard transceiver. More setup upfront, cleaner long-term. Voron 2.4 needs a board with at least 7 stepper driver slots for 4× Z + X + Y + extruder.

Electronics to consider

6 products
Contender
BIGTREETECH
Octopus Pro
8 stepper drivers32-bit STM32USB / CAN
Preferred for Voron 2.4 (4-motor Z)

The community-standard mainboard for Voron 2.4. Eight driver slots handle all four Z motors plus X, Y, extruder, and a spare. Runs Klipper on STM32F446. Wide community support and extensive Voron Discord documentation make this the default recommendation.

Buy at West3D →
BIGTREETECH
Manta M8P
8 stepper driversCANbus nativeCB1 module slot
Preferred for Trident + CAN bus builds

BTT's Klipper-native board with a built-in CB1 module slot — run your entire system from one PCB without a separate Raspberry Pi. First-class CANbus support makes it an excellent choice for EBB toolboard setups, particularly on Trident builds.

Buy at Fabreeko →
BIGTREETECH
EBB36 CAN Toolboard
CANbusToolhead PCBADXL345 onboard

Moves extruder, hotend, part cooling, and probe wiring to a single toolhead PCB. Two wires (CAN + 24V) replace the full wiring loom. ADXL345 built in for input shaper measurement. A major quality-of-life upgrade for any wired build.

Buy at West3D →
Raspberry Pi Foundation
Raspberry Pi 4 (2GB)
Klipper host2GB RAMUSB / Ethernet

The standard Klipper host for Voron builds. 2GB RAM is sufficient for Klipper + Moonraker + Mainsail. Pair with a quality SD card (Samsung Endurance or equivalent). Buy only from approved resellers to avoid counterfeit units.

Buy at Approved Reseller →
BIGTREETECH
BTT Pi v1.2
Klipper hostRPi CM4 form factoreMMC storage

A Raspberry Pi alternative at a lower price point. eMMC storage is more reliable than SD cards for long-term use. Runs Klipper and Moonraker well. Community support is growing but shallower than RPi — expect more configuration DIY.

Buy at Fabreeko →
Contender
Mean Well
LRS-200-24
24V / 200WBOM specUL listed

The BOM-specified 24V PSU for Voron builds. Mean Well is the gold standard for enclosed switcher supplies — reliable, thermally stable, and UL-listed. Do not substitute a cheap clone here. This is the one part in a Voron build where you genuinely should not compromise.

Buy at Mouser / Digi-Key →

Affiliate links used — Modern Makes may earn a commission on purchases. This doesn't affect our recommendations. See disclosure.

Mainboard feature comparison

Board DriversCANHost CPUBest for 2.4Best for Trident
Octopus Pro 8 Via USB bridge External (RPi / BTT Pi) ✓ Primary ✓ Good
Manta M8P 8 Native CB1 module slot ✓ Good ✓ Primary

Both boards run Klipper and support all Voron features. "Primary" = the community's first recommendation for that printer model.